Phone:086+0635-5638235 Fax:086+0635-5638808 Email:xkte@xinkaite.com
Home About us Products News Honor Workshop Contact us
Product list
Deep Groove Ball Bearing
KA Nylon Retainer Bearing
Deep Groove Ball Bearing
Black Chamfer lmported Process Bearing
35 Class Spherical Roller Bearing
36 Class Spherical Roller Bearing
Lightweight Spherical Roller Bearing
Self-Aligning Ball Bearing
One Way Backstop Bearing
Latest models
1316 Self-Aligning Ball Bearing
1315 Self-Aligning Ball Bearing
1314 Self-Aligning Ball Bearing
1313 Self-Aligning Ball Bearing
1312 Self-Aligning Ball Bearing
1311 Self-Aligning Ball Bearing
1310 Self-Aligning Ball Bearing
1309 Self-Aligning Ball Bearing
1308 Self-Aligning Ball Bearing
24144 Lightweight Spherical Roller Bearing
24044 Lightweight Spherical Roller Bearing
23960 Lightweight Spherical Roller Bearing
23244 Lightweight Spherical Roller Bearing
 Current Location:Home - News

How to ensure the accuracy of Black-Horn Lmported Pprocess Bearing

Time:2017.12.02 News Sources:Shandong Xinkaite bearing Co.,Ltd. Views:
Is a small amount of interference under the condition of room temperature is used to suppress sleeve bearing ring face, beating with a hammer sleeve, the sleeve will be pressed into the ring balance.
Should use gasoline or kerosene cleaning dirty bearing device, boring after using, and ensure a good smooth, Black-Horn Lmported Pprocess Bearing adopted the normal fat smooth, also can be adopted very slippery. When adopting smooth fat, we should choose smooth fat without impurities, antioxidation, antirust and extreme pressure.
(1) to measure the shaft and the bearing seat hole measured, bearing precision in recognition of cooperation, cooperation request as follows: inner ring and shaft adopt interference cooperation, the amount of interference of 0 ~ +4 ~ m (under light load and high precision is 0); outer ring and the bearing hole by clearance clearance cooperation 0 ~ +6 m (but is self bearing is the end of the use of angular contact ball bearings, can also increase the gap); shaft and hole roundness error is the name of 2 m by Black-Horn Lmported Pprocess Bearing, end ring parallel degree is 2 m by the time, the shoulder end face to outside the end is 2 m by thump; bearing hole shoulder for axis is 4 m by thump; between the front cover ends to the axis is 4 m by thump.
The bearing device, the bearing is the circumference of ferrule end face on equal pressure to press into the ring, not the end face of the bearing to the top by indirect percussion machine, to avoid damage to the bearing. The filling amount of smooth fat is 30%-60% of bearing and bearing box volume, not too much.
(2) before the end of the flow is on the shaft bearing device: Black-Horn Lmported Pprocess Bearing with a clean wash oil to stop completely cleaned up, a fat smooth, first will contain 3% to 5% of the grease into the bearing for deoxidation inorganic solvent after cleaning, and the capacity of light gun grease filled bearing (bearing for the time the volume of 10% to 15%); heating to 30 DEG C so that the pressure bearing 20, electricity press the bearing into the shaft end; the locking sleeve is on the shaft and to fit the pressure against the end surface of the bearing axial positioning; will spring balance tape is bearing on the outer ring, change the pre load launch way check the rules for the measurement of angular momentum can have large width (even Black-Horn Lmported Pprocess Bearing can be very accurate, but because cooperation or maintain frame deformation, pre load also changes). If a small amount of device is used, a hydraulic press can be adopted. With the Black-Horn Lmported Pprocess Bearing sealing structure has been filled with good grease, the user can not stop the indirect use, can be cleaned up. When pressing, the outer end face and shell should shoulder face protection, the end face of the inner ring and shaft shoulder face pressing, without permission of clearance.
Copyright © Shandong Xinkaite bearing Co.,Ltd. Phone:086+0635-5638235  Fax:086+0635-5638808  Email:xkte@xinkaite.com 我要啦免费统计